DIY fishing tents for winter fishing. Making a tent with your own hands

America

If a folded metal fan is bent in the middle by 45 degrees and then unfolded, you will get a miniature tent. A homemade winter tent was made on this principle. The tent is quadrangular, but there are five poles - the fifth pole when “closing” the tent is superimposed on the fourth. It is convenient to transport it in a case 1 meter high and 15 centimeters in diameter. Total weight 3 kilograms. Disassembly and assembly takes no more than a minute.

Homemade tent diagram

Fig. 1 Homemade tent unfolded: 1 - stand, rigidly fixed; 2, 3, 4, 5 - movable racks

Fig.2 Homemade tent folded for moving to a new place

Fig.3 Homemade tent in transport position

Fig.4 The top of the awning, covered with oilcloth or tarpaulin and pressed with a wing bolt.

The frame of a homemade winter tent is made of aluminum ski poles. On the top plate (duralumin 3 millimeters thick), let’s call it a “circle,” three M6 bolts with solid threads are rigidly installed from bottom to top, which are the axes of rotation of racks 2, 3, 4 and 5.

Rack 1 is fixed rigidly. Each bolt on top of the plate is tightly tightened with a nut. The middle bolt rises above the two side bolts in such a way that posts 4 and 5 pass freely over them.

In the front part of the circle, a plate with bends for the hooks of posts 2 and 3 is rigidly fixed at the bottom; hooks secure the poles when the tent is fully opened. Racks 4 and 5 can be in an intermediate position - next to racks 2 and 3 or connected to each other.

All racks, except the fifth one, have spacers that keep them from folding inward. When unfolding a homemade tent, you need to press each one with your hand, and when folding, pull it towards you.

For greater lateral stability of a homemade tent, posts 1, 2 and 3 are connected to each other by crosses made of narrow braid. The crosspieces also protect the plastic film from being “pushed” by the wind into the tent.

The awning is made of polyethylene film. Ribbons are sewn onto the awning from the outside and inside against each post using a stitch with a large pitch. To attach the awning to the frame, ties are sewn to the awning against each break in the posts and the bottom of the posts. At the top of the awning, the film is carefully collected and covered with a cap made of oilcloth or tarpaulin and not tightly clamped with a wing bolt.

It is advisable to fold the tent in the direction of the wind so that the awning moves away from the poles. If this is not done, the tent may be cut by the struts. When there is no wind, you just need to straighten the awning with your hand, then in one motion fold the poles, straighten the film and put it in the cover the same way you put an umbrella.

All parts and components of the tent design are easy to manufacture, and there is no need to describe the technology in detail. The connections are like a camp cot, but with bolts and nuts. If you replace them with rivets, the tent will become even lighter.

In order not to envy your fellow fishermen who are hiding in reliable shelters from the severe frost and the prickly, angry wind, make a homemade tent for winter fishing. Do perhaps unusual work with your own hands. Then staying on the pond during the cold season will become even more comfortable and memorable.

Let's figure out what the tents offered by various companies for fishermen are. There are many interesting solutions to such a problem as shelter from bad weather on a winter pond. However, all design options for such devices can be reduced to three main groups:

Frame device. A tent consists of a collapsible frame, usually rectangular or prismatic in shape. A canvas cover is placed on the frame.
Umbrella device. The shelter frame consists of an easily assembled structure, created according to the principle of an umbrella. A canvas cover is also placed on top.
Automatic device. Very popular recently are designs with an automatically folding frame with already stretched water-repellent fabric. What is attractive about such devices is the speed and ease of setting up a tent.

If prices for factory-made products are prohibitive, consider a DIY project. With your own hands you can make a device that will satisfy all the personal wishes and individual characteristics of the fisherman. After all, all people are of different heights, weights and constitutions. Some people love space, some love comfort and convenience, and some love simplicity and reliability. There may be a need to take into account the characteristics of local reservoirs and weather conditions.

The main thing for a winter shelter is reliability, ease of assembly and the ability to quickly move. Staying on a pond in winter requires significant and frequent changes in fishing spots, so think about these important requirements for future shelter.

It is important to carefully and correctly select materials for manufacturing. The fabric for covering should be light, waterproof, but at the same time breathable and retain heat well. Pay special attention to thermal insulation. The main purpose of such a device is to keep warm.

For the frame, choose a light and durable material. An old folding bed made of aluminum pipes, ski poles or durable and lightweight tubes are an excellent option for making a winter tent frame with your own hands.

Think in advance about how you will assemble and move your creation, and how to heat it, if necessary. Before you start manufacturing, it is important to calculate the costs and think carefully about all the tasks to be solved.

The procedure for manufacturing the structure

So, the question arose of how to make a tent with your own hands, where to start, what is the manufacturing sequence. Here is a simple diagram of the sequence of steps of what is needed, so that you end up with the desired shelter:

A self-made tent will help you not to pay attention to the weather. No frost or wind will stop you from enjoying what you love.

During winter fishing, the fisherman needs to protect himself from many weather conditions that are acceptable in winter, and for this, a winter fishing tent is very suitable.

In addition, it increases the time the fisherman stays in cold weather. If you use heating devices in the tent, then the air in it can be heated to 20 degrees and you can freely stay in it without outer clothing.

Types of winter fishing tents

Winter tents are divided into types, which determine their design, installation and assembly.

Umbrella. This type is considered the simplest in its design. It has an umbrella design, making it easy to install and assemble. To make the frame, duralumin rods are used, which increase the reliability and strength of the tent. The awning can be made of synthetic fabrics or a combination with tarpaulin.
Machine. The scheme of their construction is that a tent is sewn to the frame. When assembling, it is enough to twist it into a circle, and it unfolds instantly due to the action of the frame, which works like a spring. Such tents are becoming increasingly popular among fishermen because they have a low price and light weight. But along with this, it has many disadvantages: poor resistance to wind, the frame easily breaks if the tent is not laid out correctly.
Frame. Its design resembles the usual summer version. It folds out of several folding arches and an awning. She sorts it out in about 10 minutes, or even more. The tent is not particularly reliable. It is rare for fishermen to purchase this type of winter tent.

What requirements must a homemade tent for winter fishing meet?

A winter tent should create the most favorable conditions on cold, windy, winter days. In addition, it should serve as a place where you can cook a meal, drink hot tea and just warm up.

Nowadays the market is full of all possible types of tents, but it is still nice to make one yourself. If you are sewing a tent yourself, you must meet certain requirements:

It should be light and compact.
Since it is portable, the tent must be mobile.
Select fabrics that are dense.
It should be assembled and unpacked conveniently and quickly.
When making it, it is better to give preference to stronger and more reliable materials. The heat in the middle of the structure should be maintained for as long as possible.

What materials and tools will you need?

A very common homemade winter fishing tent is a design based on a fishing box. It can be bought at any store that specializes in selling fishing gear. In addition, you will also need some accessories:

Skis, two pairs (children's and school version)
Tubes, you can use ski poles.
An old folding bed.
Thick fabric, tarpaulin is best.

At first glance, it is not entirely clear what this design will look like. But, in practice, its effectiveness and ease of use have been proven. After completing the design, you should end up with a box that can be transported using skis. In addition, it is easy to assemble and move even on ice.

Drawings of a homemade winter tent

As you can see from the diagram, the tent is mounted on skis and this makes it easier to secure it on the ice. After all, mounting regular winter tents requires a lot of time and effort. And with such a design, the fisherman can move around the reservoir many times. Wherever a new hole is made, the angler drags it towards him and, having climbed inside, is ready for fishing in warmth and comfort.

Note! To reduce windage and make it easier to drag the tent in strong winds, you need to remove the awning from the tent. If you don’t do this, it will simply be difficult to drag it.

Step by step instructions

This design is very old, but very reliable. More than one generation of fishermen have tested it in practice.

How to make a tent with your own hands photo and pattern

Ski poles will serve as a frame, where they are installed vertically. Horizontal tubes should be an order of magnitude thinner. The upper nodes must be made in the form of a triple connecting adapter and its end is made like a cylinder. It is worth noting that the diameters of the cylinder and the tubes with which they are connected must match.
Next, the tubes are secured in a vertical position to the skis. A T-shaped tongue is inserted into a metal plate attached to the ski, which is located at the lower end of the tube. After this, the tube is rotated 90 degrees.
Two tubes taken from a folding bed serve to connect the frame to the box. The end of the connecting product is secured to the end of the bent tube. The latch is installed at the other end of the tube.
Eyelets made from copper strip will serve to connect the box with the tubes.
At the end of all the work, all that remains is to pull the awning. Metal plates with slots are installed in its lower part. You need to insert staples into these slots, which are driven into the side ends of the skis. The connections are secured with laces. In order for the structure to remain stable on a frozen body of water, it must be equipped with two anchors.

Homemade tent pegs and screws

In order to make pegs that will be used for a winter tent, you need to take long and strong screws. The peg has a hook-shaped top. This process is performed using pliers. Screws are made of metal tubes that have threads. If you don’t have one, then self-tapping screws will do just fine.

How to sew a tent with your own hands in the form of a house

You can consider another very popular type of tents, which are made in the form of a house. To make such a tent yourself you will need:

Fabric that does not get wet - 14 sq. m.
Metal washers – diameter 1.5 mm (up to 20 pcs.)
Braided rope – 15 meters.
Not a wide tape - 9 meters.
Rubberized fabric for bedding - 6 meters.

Having prepared all the materials, you can proceed to making a tent that can accommodate one or two people. To begin, cut out 2 pieces of fabric of the same size - 1.8 by 0.9 meters. A marking of 65 centimeters is made along the long side, and the same operation is performed on the other side. The fabric is cut at the connection points. This creates the entrance and back wall of the tent.

The diagram shows how to complete all other work step by step. The only thing you need to remember is that all the elements are sewn together with high quality. This is where tape will come to the rescue to strengthen the seams.

If regular fabric is used for the tent, then additionally polyethylene will need to be used. Rings are also sewn into the tarp so that the tent can be reinforced.

Assembling the tent on site

Assembling the entire structure takes a little time and effort:

Skis, the tongues of which are inserted into the slots of the plates, are connected to the halves of bent tubes, which should be located along the axis of the ski, and at the same time the ends are turned inside the tent by 90 degrees.
The ends of each pair of bent tubes are threaded through special holes on the ski racks.
The skis are connected to each other to create a rectangular shape.
Then a box is installed on this structure.
At the ends of the skis, four vertical pipes are installed, which serve as racks.
The roof pipes are connected using a tee. Connecting parts are installed at the ends of vertical tubes.
After aligning the holes of the tubes and tees, the installation wires are pulled into them.
A tarpaulin is stretched over the frame and secured with laces.

Disassembly of the structure is carried out in the reverse order. To make the process faster, you can number the parts.

So, despite the fact that there are many different types of fishing winter tents, homemade, time-tested ones have not been canceled. They are easy enough to make yourself. But we must remember that they must meet all the requirements of the fisherman. After all, it becomes a temporary home and shelter from the frost.

When making a tent yourself, you should carefully design it and select high-quality materials.

DIY winter fishing tent - step by step guide

I thought for a long time about how to keep warm in a single-layer umbrella-type tent; I don’t want to carry a cot with me like some fishermen do. Using a gas stove for heating, it turns out that warm air stands under the dome of the tent, and instantly evaporates through the single-layer fabric, and below, as always, it is cold. Sitting on a fishing box, your feet get cold, and you can’t sleep at night. Due to temperature changes, condensation forms on the walls of the winter tent, and then turns into a crust of ice.

Accordingly, two problems need to be solved:

Close the ice.
Insulate tent fabric

Wandering around a construction store, I came across some kind of insulation called “Izolon”. The thickness is 10 mm, and the price per linear meter is quite affordable, so you won’t regret it if nothing comes of your idea.

Its height is 1500 mm, the length was 2 meters, the total result was a piece of 2000 mm by 1500 mm. I laid him on the floor of the tent, that is, on the snow. The cold from the ice stopped. Not the entire perimeter of the tent was closed; the open area was just enough for four holes, two per angler.

This piece was enough for two backpacks (so as not to stand on the snow) and two fishermen. You can sit comfortably, even without shoes, wearing only socks; if you lie down on a jack, you can sleep quite comfortably.

You can roll it into a roll (personally, it’s not convenient for me) or like paper, put the drag on top of the sled and reinforce it with rubber stretchers. Task number one - to cover the ice and snow inside the tent and prevent the entry of cold - has been solved.

Let's move on to solving the second problem - insulating the tent itself around the perimeter, i.e. strengthen the protection of the tent from the wind blowing away heat.

I found an old Soviet rag tent at home, I bought a new one, but I don’t need this one. I laid it out, figured it out, made a couple of cuts, a hole approximately in the center of the roof. It turned out to be a slip-on cover.

The fabric of the Soviet tent is quite thick, it lies with folds, this creates a small layer of air, which is good for retaining heat.

The door of the Soviet tent was combined with the door of the main one.

As a result, the heat inside the tent remains 4-6 times longer, the gas burner before the tent was redesigned worked at maximum flame for about 14 hours, after which the 5-liter cylinder ran out, now the flame is half as much, it’s hot inside, you can sit without shoes in a T-shirt.

Condensation does not form on the walls, the tent is dry. And, what is also important, it is no longer blown by the wind. Tested in cold weather -21°C. It became darker inside, a ceiling light solves the problem.

The cover is rolled up, length 40 cm, thickness 25 cm, weight 1.3 kg.
Task number two - insulating the umbrella tent around the perimeter and increasing wind protection - has been solved.

As they say, “It’s warm, it’s light and the flies won’t bite.”

Reshetnikov Ilya, Nizhny Tagil, Sverdlovsk region, Russian Federation - Especially for Homemade FISH

How to make a floor in a winter tent
Heating a winter tent with candles

Winter fishing is a lot of positive emotions, which can be diluted by some of the negative emotions associated with weather conditions. It is not difficult to imagine the discomfort an angler feels in the presence of frost, and even wind, which increases the feeling of cold. The wind may not be strong, but it can bring a lot of problems. If you have a winter tent for fishing, then some of the problems can be reduced to zero.

The presence of a tent allows you to increase the total time a fisherman spends on a pond in winter. Moreover, you can easily raise the temperature in the tent to above zero, which will allow the fisherman to feel very comfortable.

Depending on the design features, winter tents are divided into specific models.

Umbrella

These are the simplest designs that are easy to assemble and install. To make the frame of such a tent, you should use durable but lightweight materials. Synthetic fabrics or their combinations with tarpaulin are more suitable as an awning for covering.

Machine

The design is designed in such a way that the frame acts as a spring, which takes the desired shape when it is released from the packaging. They are quite popular due to their simplicity of design and lightness. Despite this, these tents have a number of disadvantages. Firstly, they are not resistant to strong winds, and secondly, they are not so easy to fold. Therefore, when going fishing, you will have to practice beforehand. It unfolds itself, but without the skills, it will be very difficult to fold it and if you overdo it, you can break it.

Frame

This tent consists of several folding poles and an awning that covers this frame. We can safely say that this is the same simple option, but it takes a long time to assemble and disassemble. In addition, it is not particularly durable. Therefore, fishermen rarely purchase such a design.

Requirements for a homemade tent for winter fishing

A tent for winter fishing should protect the fisherman from wind, frost and precipitation. Moreover, the tent should have enough space to relax so that you can cook lunch or just drink tea to keep warm.

In specialized retail outlets you can purchase any tent, especially since the assortment is very large. Be that as it may, some fishermen make them themselves, taking into account all the requirements. Besides, who else but the fishermen knows what kind of tent is needed. Moreover, not all factory-made models meet the requirements of winter fishing enthusiasts.

A homemade tent should be:

quite light and compact;
mobile so that you can move easily;
covered with dense but breathable fabric;
easy to install and dismantle;
durable and strong, and also retain heat for a long time.

To work you will have to stock up on these tools

Most tents made by anglers themselves fit into a fishing box. By the way, you can also make a box yourself, which is what many fishermen do, although you can also buy it. In addition to the box, you will need the following accessories:

two pairs of skis, one for children, one for school;
tubes. In this case, it could be ski poles;
unnecessary folding bed;
dense fabric, such as tarpaulin.

At first glance, how can you build a tent from such a set of elements? But, nevertheless, such a design proved that it has the right to life. The final product fits into a fishing box, which is very easy to transport on ice. The structure is quickly and easily assembled and just as easily moved on ice in working condition.

The only negative is that there is little space in it. But if you approach the problem constructively, then it is possible to solve it and increase the size of the tent. Paradoxically, it protects from the cold, and this is the main thing.

Drawings of a homemade winter tent

Judging by the drawings, the tent is mounted on skis, which simplifies its installation on ice. Regular tents require special fasteners. In addition, skis allow you to move the entire structure around the pond countless times. As a rule, winter fishing is not limited to one punched hole - there can be ten, or even more, and each hole has to be fished.

The only thing is that it is problematic to use it in the presence of strong wind, since it is mounted on skis, the wind will be able to move it across the pond on its own. In this case, you can get used to it and use the power of the wind to move it. The main thing is to drill the holes correctly.

Step-by-step production

Despite the fact that this design was born a long time ago, many anglers have tested it in harsh winter conditions.

How to make a tent with your own hands

Ski poles act as a frame and are installed vertically. Horizontal tubes should be thinner. At the corners, the frame is connected using tees, the diameter of which must match the diameter of both vertical and horizontal tubes.
The next step is to attach the vertical tubes to the skis. A metal plate is attached to the ski, into which a tongue is inserted in the letter T, attached to the lower end of the tube. To secure the stick, just rotate it at an angle of 90 degrees.
Two sticks are prepared from an old cot that will connect the frame to the box. Take a bent tube, at the end of which there is a docking unit. At the other end of the tube there is a latch, which serves as a fastening element for the docking unit.
A spring is made from a copper strip that connects the box to the tubes.
Finally, all that remains is to pull up the awning. Metal strips with holes are attached to the lower part of the awning. The brackets attached to the ends of the skis are pulled into these holes. The awning is connected to the brackets using ropes. For stable behavior of the tent on ice, it is equipped with two anchors.

How to make fasteners

If the tent is not secured on the ice, then at the slightest movement it will shift in any direction, especially in the presence of wind. Therefore, you need to make special pegs with threads at the end. For this purpose, long and strong self-tapping screws are suitable, the top of which is bent in the form of a hook. By the way, hardware stores sell hooks with threads of any size.

How to sew a tent with your own hands

Alternatively, you can make a tent in the form of a house. To make it you need to take:

Water-repellent fabric with an area of 14 square meters. meters.
Metal washers, 1.5 mm in diameter, 20 pcs.
Braided rope, up to 15 m long.
Narrow ribbon, about 9 m long.
Fabric for bedding, rubberized within 6 m.

Such a tent can accommodate one or even two people. First of all, you need to prepare two pieces of fabric measuring 1.8 x 0.9 m. Marks are made on the 1.8 m side every 65 centimeters. The same is done with the other (0.9 m) side. The fabric should be cut at the joining points to create the entrance and back wall of the tent.

The diagram shows the implementation of further work step by step. Most importantly, all parts must be sewn securely. Use tape to reinforce the seams. There are times when a tent is made from ordinary fabric. In case of bad weather, polyethylene film is used, which can protect against wind and precipitation. Metal rings are sewn into the fabric for fastening. As a rule, they are located at the bottom of the awning, as well as in the places where the fabric is attached to the frame.

Setting up a tent on a pond

Assembling a homemade tent on skis takes a minimum of useful time:

The skis on which the tongues are attached are connected to the halves of the tubes located parallel to the skis. They should be directed towards the inside of the tent.
Each pair of bent tubes is threaded through special holes located on the ski racks.
The skis are connected to each other to form a rectangle.
A fishing box is installed on the structure prepared in this way.
Vertical posts are installed at the ends of each ski. There should be four of them.
Tees are taken and with the help of them a roof is formed. They are installed on each vertical post.
Using horizontal tubes, the frame is finally formed.
Fabric is thrown over the frame, which is attached to the frame using short ropes.

A similar tent is disassembled in the reverse order. If each structural element is numbered, the process of assembly and disassembly will take slightly less precious time.

Naturally, a tent can be purchased in a store, but not every winter fishing enthusiast is ready to purchase one, due to the lack of extra funds. It is much cheaper and easier to make it yourself.

The arrival of winter, with its sub-zero temperatures, piercing winds and prickly drifting snow, does not mean that going out into nature should be postponed until next summer. Of course, most people prefer to sit peacefully in warm apartments, but there are those who are not at all afraid of -20 on the thermometer. They prepare winter fishing equipment, select warm clothes and shoes, and apply maximum ingenuity in such matters as insulating a tent. This completely solvable problem should be considered based on their experience.

Correct location

Tent location in winter

Any more or less experienced fisherman will tell you that putting up a tent on a pond in a place convenient for you, where the shore or trees can protect from the wind, is not fishing - it’s just a hiking trip. The fish gather in places that are convenient for them. She, of course, takes into account climatic and relief features, but they are often radically different from our preferences. Therefore, lovers of winter fishing have developed some rules for installing a tent, which can be applied under other conditions.

The main source of cold in open space is not frost, but wind. You can protect yourself from the cold with quality clothing. It is much more difficult to hide from the wind. That is why the tent should be installed so that the entrance is on the leeward side, and to prevent blowing, it is recommended to sprinkle the lower perimeter with snow.

Insulation methods

Insulating a winter tent with polyethylene

There can be several ways to insulate a tent with your own hands. Some of them can be used in combination, some exclude the rest. You can only choose after trying several times, but we will try to carefully consider the most popular ones to make your choice easier.

Insulating a winter tent with polyethylene. The most affordable way to help protect yourself from rain and snow. However, he cannot save for long. Condensation will accumulate on the inside, and the material itself is quite light and it will be necessary to carefully secure it, at least with clothespins, and this will greatly increase the installation time of the tent.
Double tent. Or an additional awning, which can be easily made from an old tent or a special cover can be sewn, for example from tarpaulin. This method is much more effective than polyethylene insulation, but requires additional preparation at home.
Internal insulation. In specialized stores you can find a wide selection of isothermal insulation based on padding polyester, silicone and the like. They are covered with double-sided breathable fabric and provide excellent protection from moisture. Their cost, of course, is quite decent, but they also provide a solid guarantee of heat. There is also a more budget option: a heat reflector on foil, secured to the inner walls with clamps. You will have to tinker with it in the cold, but the heat from the heater will linger inside the tent much longer.
Insulated floors. The main source of cold inside the tent is frozen ground, snow or ice if you are fishing. The simplest solution to cutting off this source is to use travel rugs. They are made of a special porous material and are intended specifically for this purpose. But it should be borne in mind that after some time they will begin to transmit heat downwards, which can lead to the melting of ice or snow and the formation of an elementary puddle right in the middle of the tent.

The listed methods, individually or in combination, will help keep the tent warm for a while and are used everywhere, especially if you are planning to be in nature for only a few hours. However, this is often not enough to spend the night on a pond or in a winter forest.

Forced heating

Paraffin candles

The most effective way to insulate a winter tent is to use simple or complex heating devices or objects.

The most affordable in this regard are ordinary paraffin candles. If the temperature is not too low, they will cope with this task quite well, especially if you place the candle in a thermos flask. This achieves two goals at once. Firstly, safety increases significantly, because even if you accidentally knock over such a heat source, you will not set anything on fire. Secondly, the flask itself warms up from the candle fire and begins to intensely radiate heat.
In second place is the old, proven method of heating a tent using a hot stone. However, you will have to find this very stone, which is somewhat difficult to do in winter. Then make a fire, heat the stone on a live flame and bring it into the tent. To prevent it from burning the floor and melting the ice on the floor, you can place it in a metal pot, which, by the way, will increase the operating time of such a “heater,” or wrap it in several layers of foil.
Gas heater. A special compact device running on liquefied gas, designed specifically for tourists, fishermen and other outdoor enthusiasts. There can be two types depending on the nozzle:
With metal nozzle.
With ceramic nozzle.

They are very easy to use and do not take up much space, but their operation is limited by the size of a stationary cylinder, so it is better to take a spare one with you.

Gasoline heater. There are compact and inexpensive models. Unlike gas ones, they are even more unpretentious, but the fire hazard increases significantly. Requires increased attention and caution.
And, of course, a wood-burning stove. Not very convenient for transportation. Of all the above options, heating a winter tent using a compact stove can be called the most ideal.

There is no need to be afraid of frost and hide your noses behind double-glazed windows and an insulated safe door. A winter trip to the bosom of nature, if well prepared for it, will give you indescribable pleasure, give you a huge boost of energy and lift your spirits for more than a day or two.

Types of tents for ice fishing

Depending on the design features, winter tents are divided into specific models.

A homemade tent should be:

quite light and compact;
mobile so that you can move easily;
covered with dense but breathable fabric;
easy to install and dismantle;
durable and strong, and also retain heat for a long time.

To work you will have to stock up on these tools

two pairs of skis, one for children, one for school;
tubes. In this case, it could be ski poles;
unnecessary folding bed;
dense fabric, such as tarpaulin.

Despite the fact that this design was born a long time ago, many anglers have tested it in harsh winter conditions.

How to make a tent with your own hands

Ski poles act as a frame and are installed vertically. Horizontal tubes should be thinner. At the corners, the frame is connected using tees, the diameter of which must match the diameter of both vertical and horizontal tubes.
The next step is to attach the vertical tubes to the skis. A metal plate is attached to the ski, into which a tongue is inserted in the letter T, attached to the lower end of the tube. To secure the stick, just rotate it at an angle of 90 degrees.
Two sticks are prepared from an old cot that will connect the frame to the box. Take a bent tube, at the end of which there is a docking unit. At the other end of the tube there is a latch, which serves as a fastening element for the docking unit.
A spring is made from a copper strip that connects the box to the tubes.
Finally, all that remains is to pull up the awning. Metal strips with holes are attached to the lower part of the awning. The brackets attached to the ends of the skis are pulled into these holes. The awning is connected to the brackets using ropes. For stable behavior of the tent on ice, it is equipped with two anchors.

How to make fasteners

How to sew a tent with your own hands

Alternatively, you can make a tent in the form of a house. To make it you need to take:

Water-repellent fabric with an area of 14 square meters. meters.
Metal washers, 1.5 mm in diameter, 20 pcs.
Braided rope, up to 15 m long.
Narrow ribbon, about 9 m long.
Fabric for bedding, rubberized within 6 m.

Setting up a tent on a pond

Assembling a homemade tent on skis takes a minimum of useful time:

The skis on which the tongues are attached are connected to the halves of the tubes located parallel to the skis. They should be directed towards the inside of the tent.
Each pair of bent tubes is threaded through special holes located on the ski racks.
The skis are connected to each other to form a rectangle.
A fishing box is installed on the structure prepared in this way.
Vertical posts are installed at the ends of each ski. There should be four of them.
Tees are taken and with the help of them a roof is formed. They are installed on each vertical post.
Using horizontal tubes, the frame is finally formed.
Fabric is thrown over the frame, which is attached to the frame using short ropes.

A similar tent is disassembled in the reverse order. If each structural element is numbered, the process of assembly and disassembly will take slightly less precious time.

Naturally, a tent can be purchased in a store, but not every winter fishing enthusiast is ready to purchase one, due to the lack of extra funds. It is much cheaper and easier to make it yourself.

Do-it-yourself water jet for a boat

How to make a hinged transom for a PVC boat?…

Homemade fishing rod stand

DIY nod for a winter fishing rod

DIY winter lures for perch

Do-it-yourself snowmobile for fishing

Do-it-yourself self-hooking winter fishing rod...

DIY fishing boat

Making a spinner with your own hands

Tents for winter fishing

Just some twenty years ago, a factory tent for winter fishing was a rarity in our country. On the ice you could often find homemade tents of a wide variety of designs. The simplest options were a large plastic bag, one edge of which was attached to the handle of a drill screwed into the ice, and the other was supported by the fisherman himself with his shoulders and head. The lower edge of the tent bag was pressed against the ice by a box on which the fisherman sat. Fishing in such a tent was sheer torture, so many fishermen, especially fishermen, sewed reliable and spacious tents of original designs. In addition, drawings and diagrams of winter tents were periodically published in the “Homemade” section of the “Rybolov” magazine.

Today, probably, few people sew their own tents. At least, they are almost never found in reservoirs. After all, it is much easier (and, perhaps, cheaper) to buy a ready-made tent. The stores offer a wide variety of options - for every taste and budget.

Chinese spring tents or, as they are called, “machine guns”

The simplest and most budget option are Chinese spring tents or, as they are called, “automatic tents”. They are sold under the brands “Condor”, “Siwedia”, etc. Price -600-1500 rubles. - depends on the size, presence of a bottom and thickness of the material. The awning of such a tent is attached to a frame made of spring wire, which is folded into a figure eight. The advantage of such tents is their compactness - when assembled, a one-person tent in a cover is a flat pancake with a diameter of 50 cm, a thickness of 5 cm and a weight of 2 kg. The tent unfolds on the ice itself - just take it out of the cover.

However, these tents also have their drawbacks - they are unstable in the wind, and additional fasteners are not included in the tent package. Tents of this type are usually sprinkled with snow around the perimeter, but this is done more for insulation. Snow will not help hold up a tent in a strong wind. For reliable fastening, you need to separately purchase special “screws” that are screwed into the ice. The simplest gimlets, made from self-tapping screws and resembling a bottle corkscrew, are sold at a price of 100 rubles for 4 pieces. A set of real, “alpine” gates will cost you more than the tent itself. Spring type tents come with or without a bottom. A tent with a bottom that fastens with a zipper is preferable, since it does not need to be covered with snow around the perimeter, and the fisherman, pressing down the bottom with his own weight, makes the tent more stable in the wind.

Cheap Chinese tents very often require modifications - strengthening the hinges, sometimes replacing the zippers. Such tents are usually made from thin polyester, which protects well from wind and wet snow, but does not “breathe” at all. Ventilation of the tent is carried out through a window and a slightly open “door”. There are also two- and even three-layer spring tents. They cost more accordingly. It seems like no one succeeds in assembling this type of tent the first time. Therefore, after purchasing, it makes sense to practice at home. The sequence of actions when assembling a tent is usually depicted in a diagram included in the pocket of the cover bag. After several fishing trips, you will learn how to fold an automatic tent in a figure eight shape and put it away in a cover in a few seconds.

Another common type of tent for ice fishing is the umbrella type tent.

They are produced not only abroad, but also in Russia, under the brands “Nadezhda”, “Malek”, “Nelma”, etc. Tents of this type have a rigid frame, usually made of durable duralumin, which opens like an umbrella. Such tents are more reliable and stable. There are 2, 4 and 6-beam designs. The latter, of course, are the most stable. In the production of these tents, mainly materials of higher quality and strength are used than for spring-type tents.

If the name of the tent contains the index “D” (for example, “Stack-Al D”), then this indicates that the upper part of the tent is made of “breathable” fabric. In such tents, condensation practically does not form in frosty weather. In addition, you can use heaters without fear of burning. However, given that ordinary tarpaulin is most often used as a “breathable” fabric, in wet weather the roof of such a tent begins to let in moisture, which drips directly onto the fisherman. Tents of this type are also disassembled and assembled quite quickly. When folded, they are not as compact as machine guns and are a cylindrical cover 1.2 m long. The weight of a single tent is about 3 kg. The cost of umbrella tents is from 3 to 6 thousand rubles.

Tents from Western manufacturers - “Maverick”, “Rapala”, “AVIREX”

Today the market offers a wide range of “branded” tents from Western manufacturers - “Maverick”, “Rapala”, “AVIREX”, etc. These tents are distinguished by high quality tent materials, durable poles made of composite materials, reliable fasteners and fastenings, good a well-thought-out ventilation system through special membranes and maximum ease of assembly, disassembly and operation. Of course, their price is 2-3 times higher. Also, we should not forget that serious tents have a very decent weight. For example, the luxurious three-seater “Rapala Pop-up Tent 3-Man” (costing from 15 thousand rubles), the developers of which, it seems, took into account absolutely all the nuances of winter fishing, has a weight of 10.4 kg. As for the capacity of the tent, here you need to follow the “-1” rule. Those. If the tent is “double”, then in practice one angler can comfortably accommodate and fish in it. If “three-seater” - then two.

Some fishermen use universal “winter-summer” type tents in winter, or summer tents in general; however, the presence of an additional awning and canopy in winter only creates additional inconvenience and increases disassembly and assembly time. A number of anglers prefer professional alpine tents. Considering the high (from $1 thousand) cost of the latter, this is hardly advisable. However, the choice always remains with the buyer.

Awnings according to their purpose are divided into:

intended for parking;
for swimming;
for transportation.

Parking

Protect the boat from external factors when laying up. The awning completely covers the boat, turning it into a vessel, which, for example, allows necessary repair work to be carried out under the roof.

the motor is tightly closed and protected from water ingress;
fastening is done with cords threaded into special rings of the awning design fittings;
The simple design ensures fast, reliable and durable installation.

Swim awnings

Nasal. Performs the function of protection against splashing water. Installed on the bow of the boat. Options:
- with viewing glass;
- without viewing glass.
- Specifications:
- primary colors of green and gray;
- small volume and weight;
- easy installation;
- aerodynamic shape that helps maintain initial speed and stability.
Running gear. The awning reliably protects the fisherman from exposure to the sun, wind and water. Consists of front, side and rear structural elements. There are 2 types of awnings by design:
- with one-piece elements;
- with connected elements.
Transformer. This variety is the best option for protection and convenience. The unique name was obtained due to the presence of six transformation positions, through which ventilation is ensured, as well as fishing on inclement days. Made in a tent style, with easy installation and use, taking into account the complete cover of the boat.
Frame. These awnings are also called “roof awnings”. Provide protection for the fisherman and his accessories from excessive exposure to the sun's rays and precipitation. Quite easy to install and use awning. The presence of high strength and long-term use are its characteristic distinguishing features.

Transportation

The function is to reliably protect the surface of the craft. As a rule, awnings should not allow moisture, dust and dirt to pass through. The “blanket” is equipped with fastening devices, through which it is firmly fixed to the boat.

How to make a cape tent

To attach the tent to the ice, it is best to use screws, which you can also make yourself. The simplest option is to weld pieces of metal rod to long screws.

You can put rubber or silicone tubes on both sides of the rod, in this case it will not cool your hands, and it will be more convenient to hold it. Such a screw can be easily screwed into the ice and then removed back.

You can also use construction screws to secure the tent. Their advantage is that they are hollow, so they are easier to screw into the ice.

At the end of each self-tapping screw, use a needle file to sharpen 3-4 sharp teeth. It is also advisable to drill a through hole that will go into the ring.

To make the screws screw in easily, you can use a piece of metal rod that will act as a handle.

DIY frame tent for winter fishing

A more complex option is making a frame tent. The frame can be made from metal or plastic pipes, connecting them using small tubes, corner and three-way hinges. With the right approach, you will get a reliable design that can be quickly assembled and disassembled. Thus, a do-it-yourself winter fishing tent can be made of any size and shape.

A frame tent can be placed on a sleigh. In this case, it will be easy to move on the ice. To make a sled, you need to use the same metal tubes and any suitable wooden or plastic skis.

The following frame materials are used:

aluminum tubes;
steel wires with spring properties;
fiberglass rods with spring properties.

The shape of the frames is either angular or arc-shaped. The characteristic properties of springing serve to firmly stretch the awning. Aluminum frames are structural, taking into account the insertion of one part into another.

What materials are used

The main material for making awnings is synthetic fabrics, nylon-based. For the manufacture of viewing parts - window, windshield - polyethylene or lavsan is used. However, long-term use affects the quality of the review. Therefore, it is better to use polyvinyl chloride-based film.

Note! PVC fabric itself is not used in the manufacture of awnings due to its roughness, heaviness and complete lack of air passage.

Making a dome tent

You can make a more complex pattern and make a dome tent. A do-it-yourself ice fishing tent in the shape of a dome will require more time to manufacture. It is not as compact for transportation as a cape, but it will also be much more convenient to fish in it.

An ice drill is not suitable as a support for a canopy. You need to prepare a special spacer with a pointed end that will stick into the ice. To make the tent easy to transport, the spreader must be collapsible. Its individual sections can be connected using metal tubes - this type of fastening was used in old bamboo fishing rods.

There should be holes along the edges of the dome for attaching the tent to the ice using spacers. Another option is to sew on loops.

Bow awning

In manufacturing, for reasons of safety, convenience and “dryness,” moisture-resistant materials and appropriate components that optimize the quality of waterproofness will be required.

First you need to decide on the exact dimensions of the boat and, if necessary, make the corresponding drawings. In addition, to determine the fastening of the frame, it is necessary to inspect the fastening fittings located on the sides of the boat.

Note! The first manufacturing steps are carried out by making an approximate size pattern on a “test” fabric, after which the sketch is transferred to the base material. At the same time, we must not forget about the additional allowance of fabric to form a “sleeve” for passing the fastening.

DIY winter fishing tent - making a floor

It is not necessary to make a floor for the tent, but it will make fishing as comfortable as possible.

Izolon (polyethylene foam), one of the types of sheet insulation, is perfect for its manufacture.

It is better to take a variety of this material with the smallest bubbles - it is very dense and conducts heat minimally.

This flooring helps retain heat. When using it, the ice under the tent does not melt even when using powerful heating devices. In addition, all fishing accessories can be laid out on an isolon mat without having to be placed in the snow.

How to make a walking awning

The organizational stages of manufacturing this type are similar to the bow one: we determine the dimensions of the boat, the frame, and make a pattern for the awning using test material.

The following materials will be required:

a pipe for an arc measuring at least 20 mm (at least 4 m);
bracket (at least 9 pcs);
awning fabric (not less than 9 m);
nylon threads;
transparent film for window parts;
fasteners for fastening parts of the awning when folding them (at least 10 pcs);
buttons for fastening the awning.

To begin with, a frame is made: one pipe will be the carrier (large size), and the second will be mounted on the middle part of the carrier (small size).
Manufacturing occurs by bending aluminum pipes to obtain the desired shape, taking into account the dimensions of the boat and the expected ceiling height of the future awning.
Having prepared the desired shape of the arc and retreating at least 20 cm from the base of the tube, a device - a clamp, with holes for bolts - is placed in the middle of the supporting frame.
The small frame is equipped at the ends with a fastening device with a coupling to limit its rotation in one direction. With these fasteners, parts of the frame are fixed to each other with bolts. Here you need to take into account that the limiter in the fastener is located on the outside of the small frame, from the supporting one.
Having previously installed the frame on the desired part of the boat, marks are made to place the fastening spots.
The parts of the boat where the marks were made are cleaned and covered with glue. In the same way, the patches are covered and glued.
The upper edges of the frames must be equipped with clamps-rails, into which rubber shock-absorbing belts will be attached, equipped with hooks that will be attached to the front and rear parts of the boat cylinder in fastening fittings.
After installing and fixing the frames in a vertical position, as a rule, the entire structure of the running awning will be placed on them. After manufacturing and installing the frame, you will need to cut out the elements of the awning. They consist of several parts, including transparent oilcloth parts for front and side viewing.
In manufacturing and cutting, the lower parts of the side and front elements must have a spare length of up to 20 cm, where they will be folded to the inside, thereby forming a passage for the rope. The folded part must be equipped with holes for eyelets with a distance of up to 15 cm.
The side, viewing and overlapping parts of the awning must be stitched with zippers from the inside in order to combine with other elements of the awning and the frame.
At the end parts of the awning, where the zippers are sewn, it is necessary to attach push-button attachments to tightly fix the parts of the awning and prevent the zippers from opening when exposed to wind.
After making and cutting the awning, the first step is to attach the ceiling part of the awning to the frame arches. The top of the awning is stitched with three zippers. One zipper is sewn on the inside, one on the edge of the awning and one on the outer middle part between the inner and outer zippers. Here you need to take into account how the zipper wraps around the upper arc of the frame.
The awning is pulled onto the frame by attaching the outer and inner zippers to each other, taking into account the coverage of the frame arc.
An external zipper is used to secure the viewing and side parts together.

How to sew a tent awning

An awning for an ice fishing tent can be sewn in one evening, and you don’t have to be a craftsman to do it.

Before sewing the tent, individual patterns must be fastened with pins, which are positioned perpendicular to the seam; the more of them, the better.

Transformer

The transformer is one of the most difficult to manufacture. Tubes and fasteners will be required in significant quantities. In addition, the use of special glue and a number of accessories such as hooks, eyelets, and rubber accessories is provided.

All samples and sketches of tent elements must take into account the volume of the product. The peculiarity of these awnings lies in their removable characteristics. If necessary, the entire structure can be assembled on the back of the boat, following the example of a convertible.

When making frame arches, they need to be equipped with hinges to connect them together. Also, the arches should be attached to the side parts of the boat, taking into account the possibility of quick assembly with the awning fabric.
The production of arcs occurs by analogy with a running awning. Bends are made until the desired shape is obtained.
The front, small arc of the frame is attached to the middle of the supporting frame by means of a thrust hinge. This hinge is also a limiter in the rotation of the small frame outward from its position.
The sides of the frames must be equipped with clip-rails through which shock-absorbing belts will be pulled and attached to the side fittings of the boat. In this case, the frame will be firmly fixed in a vertical position.
After this, the cutting and cutting out of the awning elements on the basis of the installed frame begins.
By analogy with running awnings, the formation of transformers occurs by flashing the connecting parts between the elements of the awning with zippers.
The lower parts of the awnings must be sealed by folding the end of the awning in a double layer and stitching.
These parts are equipped with holes for grommets in which hooks will be placed in order to attach them to the side fittings of the boat cylinder.
After the top is located on the frame by closing the zipper, the visibility, side and rear parts of the awning are attached to it, also by means of zippers.
Having placed and attached all the parts of the awnings to each other, you need to pull them down using hooks and attach them to the side fittings of the boat cylinder.
Straps are sewn at the top to hold and secure certain elements of the awning. In fact, the difference between a transformer lies in the assembly of its elements in a separate order. If necessary, you can fold the side or front parts, securing them with a fixing belt.

Parking awning

By analogy, it is designed strictly in accordance with the dimensions of the boat. The following materials are used:

waterproof material;
masking or adhesive tape;
fastening buttons or eyelets;
scissors;
markers.

Awnings of this type are made taking into account the absence of frame arches. It is necessary to completely cover the boat with awning material;
After preliminary measuring the required part of the boat, it is necessary to cut out the awning, taking into account the separation of additional dimensions along the edges, for placing fasteners, stitching sleeves, for passing a rubber cord through them;
In the covering state on the awning, measurements are taken of such auxiliary inserts as pockets, zippers;
Next, they begin cutting on a machine;
The finished covering is stretched onto the boat;
The awning should tightly cover the entire surface of the boat, its lower parts are pulled down along the entire perimeter, and attached with sewn fastening hooks (depending on the side fittings of the boat) to the fittings of the boat.

Biminitop

Another variety is roof awnings. A distinctive feature of such awnings is the absence of side walls. The design of the awning is very simple.

Materials:

waterproof material;
transparent film;
metal arcs;
belts with buckles for shock absorption;
connecting carabiners.

First you will need to prepare support parts consisting of 4 aluminum tubes.
Counting more than 20 cm from the end, support hinges are installed on the two tubes. Similar hinges are also installed at the ends of the other two tubes.
By means of hinges, a pair of tubes is attached to tubes with hinges at part of the base. When positioned vertically, the finished structure should display the letter “U”.
Based on the width of the intended boat covering surface, metal arcs are formed taking into account their connection to the support tubes.
In order to achieve the integrity of the tubes, a rod consisting of a durable rubber material can be passed along the inside of the support tubes and the frame arc, which will be attached to the base parts of the opposite support parts.
Next, on the side parts of the boat you need to place 2 spots, with a hole for passing the bolt, and on the back and front of the boat 4 carabiners, into which the support tubes will be tied by tightening the shock-absorbing belts from the frame parts to the carabiners.
After the supports are installed on the spots, you need to stretch the awning material onto the upper part of the frame.
Note! When pulling the bow poles towards the stern of the boat, the front part of the awning should be pulled more tightly so that it is at a lower level than the rear bow. Through this, the aerodynamics of the structure will not be compromised.
Having made the necessary measurements of the awning in cutting it out, you need to leave an extra 15-20 cm of material at the edges for making sealing layers.
In the compacted parts of the upper element of the awning, zippers are sewn on the front and back.
Sleeves through which nylon threads will be passed, which will be attached to the arches of the frame.
One pair of zippers is sewn from the inside of the awning, and the second pair is sewn on the extreme side of the awning.
After this, the finished awning is taken and placed on the arches of the frame, taking into account the folding of the ends of the awning onto its inner part towards the zippers sewn from the inside, fastened and fixed.

Thus, the awning is installed.

Awnings depend on the overall shape of the boats and their purpose. In the situation of using awnings for overnight stays, it is necessary to provide ventilation capabilities.
The dimensions of the boat and its features should be taken into account when the craft is inflated.
Tarpaulins are often used as awning materials. But, we must take into account the fact that tarpaulins become pliable over time when exposed to moisture. To prevent this, you need to treat the tarpaulin with a waterproof compound.